Appliances (Phone System 40) - Upgrade to v14?
@nmarques wrote: Hello, I am setting up a new Sangoma Phone System 40. Before I even get started, should I just go ahead and upgrade the distro to FreePBX 14? It came with 13. I don’t see any problems...
View ArticleTroubleshooting SIP Registration (Alerts, Recovery, Etc)
@nmarques wrote: Hi all, I am using FreePBX 14 Stable with Asterisk 13.17.2. We use VOIP.ms for DIDs. We just realized that we were not receiving calls all morning. Outgoing still worked as it doesn’t...
View ArticleUsing "User name" and "Authentication name" for SIP REGISTRATION
@jmorrison876 wrote: When registering a sip enpoint to Freepbx, the extension # is used for both the username and authentication name in the device config. Being new to Freepbx, I must ask is their a...
View ArticleNAT Configuration
@casajaguar wrote: Hi, I had installed FreePBX and configured succesfully for LAN. I’m using a DD-wrt router with dynamic ip and a VM with FreePBX installed behind. I would like to access to PBX with...
View ArticleNeed an advice about time conditioning
@akadimka wrote: Hi to all! Here’s the question. Have several extension with overlapping working time. E.g.: 1st is working from 8 a.m till 6 p.m. -> inc. calls are going to 1st ext. till 9 a.m....
View ArticleFresh Install Problems
@Telleraine wrote: Greetings Community, Hope everyone had a great holiday season. I am reaching out today in the hopes someone here can do what Google couldn’t. When I installed the latest x64 distro...
View ArticleBlack and White hardware requirements
@WQGJ587 wrote: I cant seem to find, a old fashion black and white hardware requirement list for the newest FREEPBX Distro. I find articles, that to be honest, dont say a whole lot of anything except...
View ArticleMoving from plain asterisk to freepbx
@haljbr wrote: Hello Guys. I am a little confused with all those sip_xxx.conf and extensions_xxx.conf that freepbx has. On my plain asterisk I have this configuration below and I am not sure were to...
View ArticleClik here to view.
Failure of Backups
@dporter2016 wrote: Here is what I get when running Backup (Save and Run) Posts: 1 Participants: 1 Read full topic
View ArticleHow to test Asterisk new installation?
@vlad1977 wrote: Hi everyone, I am a totally new user, looking for a guidance. Installed FreePBX 13 with the main goal to create telephony station for my small dental office. I’m at the stage of...
View ArticleInbound call is allowed to make transfer
@esarant wrote: Hello, I am really puzzled by a problem I face. I got a SIP trunk with a SIP provider. If I let the context to context=from-trunk then the caller can’t make a transfer (*2 or ##). If I...
View ArticleHow to make Chan_SIP extension work with IP phone
@kashifiqb wrote: I just added an Extension of Chan_SIP type to my Freepbx. But now when I try to connect to it using my IP Phone or Soft phone, the phones/soft phones are not getting connected. What...
View ArticleCosmetic issue after upgrade to 14 (and workaround)
@StevenA wrote: I have just completed the upgrade to 14 from 13 using the upgrade module. The UCP module load failed because of missing modules pm2 and certman, but the system came back fine with just...
View ArticleMaster/Slave APC UPS for multiple Server
@okynnor1 wrote: Hi, In FreeNAS it is possible to allow the setup of a master/slave config in order to allow multiple server to be shutdown. Is this feature available from the Web interface in...
View ArticleClik here to view.
Option 66 data altered on S500
@MacsOffice wrote: I’m using option 66 from my switch and the data is altered. Switch config: ip dhcp excluded-address 192.168.200.1 192.168.200.200 ip dhcp excluded-address 192.168.200.250...
View ArticleConfig not send Config to Sangoma S500 phones from FreePBX GUI buttons
@MacsOffice wrote: After configuring the extensions and mapping them, FreePBX will not issue the configuration to the phones using the save, rebuild and send option or the button on the right column...
View ArticleCan't open UCP
@AB81 wrote: Hello, I get this error “array_merge(): Argument #2 is not an array” when I open UCP. 7.Whoops\Exception\ErrorException...
View ArticleUnable to use Asterisk General Call Pickup *8
@lblokland wrote: Hi, Best wishs to all! I’m trying to setup call pickup (*8) but cannot get it up and running. When I dial *8 on a phone it fails, the only two lines of output in the Asterisk log...
View ArticleFreePBX Installation
@gal_bnology wrote: Hi guys, I need a new FreePBX installation for a new server. What do you recommend? Thanks!! Posts: 1 Participants: 1 Read full topic
View ArticleStrange emails
@jonnybobs wrote: Hi All, Keep getting an email from the system and can’t work out where from within or what its about. I get emails from it in other areas with no issues… hwew below is what we get....
View Article