Does Home 2 FreePBX have to be done on local network?
@johnjces wrote: Hopefully not too stupid of a question but can I run this conversion tool over the Internet on a remote system or must the New and Donor have to be on the local network? Read the Wiki...
View ArticleClik here to view.
UCP 14 add FAX Widgets Error
@jeff.wong wrote: Hi all, I have just upgraded my system from freePBX 13 to 14, and I able to add any of the widgets in UCP but except FAX, I have tried disable and enable again Fax Configuration...
View ArticleToo much delay in IAX2 calltoken timestamp from address
@mhammett wrote: [2018-06-10 21:47:31] WARNING[18226]: chan_iax2.c:5005 handle_call_token: Too much delay in IAX2 calltoken timestamp from address I ran the conversion tool to move a 2.11 PIAF install...
View ArticlePhoneBook configuration
@charneval wrote: Hi. I have a new installation of a FreePbx 14 with 8 ip phone “yealink” What is the better solution for create a shared contacts book for my phones? And when I have unanswered calls,...
View ArticleUnable to create request with auth. No auth credentials for realm(s)...
@mhammett wrote: New install of the 7 , updated. [2018-06-11 13:03:33] WARNING[26552]: res_pjsip_outbound_authenticator_digest.c:178 digest_create_request_with_auth_from_old: Endpoint: ‘XXXX’: Unable...
View ArticleContinue with IVR after recording Voicemail message
@calippo wrote: I’m using FreePBX 14.0.3.6. I would like to do this: A caller comes from an IVR, hears an announcement and leaves a message on an extensions Voicemail. After this the caller should...
View ArticleClik here to view.
FreePBX Non-functional After Power Loss
@mikeaph wrote: After losing power, when attempting to boot into FreePBX, the following is displayed. Image-1.png4032x3024 2.46 MB Posts: 1 Participants: 1 Read full topic
View ArticleUndo activation to create master image
@supersource wrote: I’m trying to create an image that I can deploy with the latest FreePBX. In order to do this so I can uniquely activate each one separately, I need to remove the activation from...
View ArticleSccp vg204
@boctroy wrote: I’m looking to switch from ccm to freepbx. We have many phones setup on our network including vg204s and vg224s using SCCP. I’d rather see if i can configure freepbx to fill in for the...
View ArticleIssue after running conversion tool
@bk6662 wrote: Hello, Just installed the latest 64-bit ISO, and then ran the conversion tool to migrate settings to my new platform. Everything went well - no errors. But now that I turned off the old...
View ArticleCalls pushed to iax2 trunk require confirmation
@supersource wrote: I’ve got a IAX2 trunk that connects two FreePBX systems working great. I have unique extensions on each system, however, there is a group of extensions, say 4xx that forwards to...
View ArticleProbelm after Module updates
@baloo1986 wrote: hello i have a problem after upgrade of Modules. When i click on APPLY i becom this error: exit: 1 Unable to continue. died in splice ext-did-0002 s in...
View ArticleDistro Conversion Tool - not converting IVR
@jsulmar wrote: I’m migrating from FreePBX 2.9 to 13 using the Distro Conversion Tool. It seemed to work great, except that my IVRs were not converted. Any advice what might have gone wrong? Posts: 1...
View ArticleSIP Trunk Provider you use?
@ecnorm wrote: Hi FPBX community! Good day. I am a newbie here. We are testing freepbx for a small office situation with need for maximum 3 lines. plus International calling, toll free inbound (U.S) -...
View ArticleFreepbx crashed after power failure
@kashifiqb wrote: Hi all, One of our telecom servers recent shut down unexpectedly due to power failure. After that when we power it ON, it gives this error: http://prntscr.com/ju95lq and doesn’t...
View ArticleCaller ID name
@Azer wrote: Hi, we have a Sangoma FreePBX connected to HiPath 3800 via SIP trunk. Trunk status is up, Calls beatween PBXs is successfully. But we have a bit problem is Caller ID name is not working...
View ArticleRecall on busy function
@claloano wrote: I would like to realize a feature that when you call a number and this number is busy you automatically activate an activity that every 3 or 4 or 5 minutes will check if that number...
View ArticlePrepend Caller-Id on Blind Transfer
@tony722 wrote: Hi, Running FreePBX 14.0.3.6. Wondering how to prepend something like "Xfer: " onto the callerID when blind transferring a call. There are several reasons but here’s one: so that when...
View ArticleCisco 7975g and FreePBX
@Christopheric1 wrote: I am having an issue with a 7975g. We have installed the Endpoint Manager module that has the template and everything for the phone. I have made sure in the tftpboot directory...
View ArticleNot able to connect slite software after new installation
@shivaramkar wrote: Hi, I have installed new freepbx , i created new sip extension. But when i try to connect the xlite it is not connecting. can someone help on this. Regards, Shivaram Posts: 1...
View Article