Failure reading sector 0x0 from hd2 after fresh install
@lhalep wrote: Hi, On a newly bought intel i5 with 16GB and 2 WD RED HDD, i installed the latest freepbx distro. After the installation I got a message failure reading sector 0x0 from hd2 press any...
View ArticleNames not updating on phones
@SiP1701 wrote: We have a client with over 60 extensions using Polycom VVX300’s, a few VVX500’s and 2 Yealink T46’s. The Polycom Phones configure via TFTP, while the Yealinks configure via HTTP. We...
View ArticleExecute Script after MixMonitor
@jaycos wrote: Hi all, I created the script test.sh to run after MixMonitor, but it doesn’t execute. Here is what does work: Asterisk seems to call the script: [2018-10-02 12:04:42]...
View ArticleClik here to view.
Root storage
@Maverick1983 wrote: Hi it’s possibile to extended / partition with /boot space? Posts: 1 Participants: 1 Read full topic
View ArticleLosing caller ID from POTS thru OBi110
@MrMoxy wrote: I have a POTS line from Comcast that I connected to my PIAF using an OBi110 as FXO port. Everything works fine EXCEPT that the caller ID is being rewritten when passed to my Panasonic...
View ArticleIVR disconnecting incoming calls
@paultgreen wrote: Since updating to IVR module version 14.0.3 we have noted that more often than not calls on the DDI which routes to our IVR menu are being terminated without the initial...
View ArticleTemporary Time Condition?
@jreach72 wrote: I have a client for which I have time group setup for normal business closures (Holidays, After 5pm until 8am, and weekends, then a time group which if it matches it goes to IVR if no...
View ArticleUpgrading from rta to freepbx
@dwsiemens wrote: Hi I have a asterisk footprint running on asterisk 11.25.1. Its a roll your own install, no gui, using RealTime asterisk. I am spending a lot of time writing dialplan. I am also...
View ArticleRecover a FreePBX installation via USB
@smoodley wrote: I am trying to recover a standalone Freepbx using the USB recovery process. The Installation goes fine and completes. When the system reboots I get the following error and system just...
View ArticleCalls forarded to Misc. Destination not passing through CID/CNAM information
@jreach72 wrote: Hey guys/gals, I am trying to setup forwarding of calls to a cell phone during “nite mode” for a client. Calls forward with no problem however the CID and CNAM information displayed...
View ArticleCan I turn a primary FreePBX 14 server into a backup?
@Beachtech wrote: I just got a new client after their FreePBX server went down and the person who set it up was MIA. So I had a small FreePBX 14 server ready to go and set it up quickly so they could...
View ArticleAdjust SMTP Server Address in Old version of FreePBX
@rschindler wrote: Hello, we have a client who is using FreePBX version 2.3.1.5 whose voicemail to email randomly stopped working. In the mail logs, I found that the SMTP host address that they are...
View ArticleHow do you install https://github.com/FreePBX-ContributedModules/endpointman
@mst wrote: How do u install this module if its not .tar??? Posts: 2 Participants: 2 Read full topic
View Article1 way audion after AtXfer Cancel
@jerryriggin wrote: We have an issue with 1 way audio where, after agent cancels attended transfer and re-connects with customer, agent can hear customer but customer can’t hear agent. These are...
View Article"Voicemail is not enabled for this extension" when trying to record greeting
@Kafluke wrote: FreePBX version 10.13.66-22 Extension has voicemail enabled and it works just fine. When the user tries to record any greeting the phone displays the message “Voicemail is not enabled...
View ArticleFreepbx with polycom vvx 410 & 411
@mst wrote: Is there any template for deploying 20 vvx410 or 411 - Polycom phone in an easier way that from each one GUI? I wonder if I can do that with Free End point. Posts: 3 Participants: 3 Read...
View ArticlePush out stored voicemails to email
@dsetech wrote: I have a voicemail box that has 15 stored voicemails in it because I forgot to configure the email options. I would like to push these voicemails out to the people who are now in the...
View ArticlePLEASE HELP! - no IP Address
@Neromarketing18 wrote: Installed Freepbx however at the end of installation it only gave me a MAC address not an IP address so I cannot get into the GUI… I don’t know what to do next, tried to...
View ArticleBlindTransfer Event not Fired
@jerryriggin wrote: I have a system that does not fire the BlindTransfer event. The transfer works perfectly, but from the CLI output below the transfer is happening in from-internal context and not...
View ArticleReload failed because retrieve_conf encountered error 255
@Chrisb45 wrote: i have updated all modules and now get the below error when applying exit: 255 Unable to continue. Class ‘ext_unpausemonitor’ not found in...
View Article